Cutting Housing Dados With Plow Plane Make a Dado Joint using a Router Plane w Bill Anderson Wood and Shop 229K subscribers Subscribe 1 4K 80K views 4 years ago Joinery Bill shows how to cut a dado joint for shelves and trim
Joinery Techniques Dados Grooves and Router Plane Best Practices Watch on Grooves Dados Using Planes and Saws Housed joinery That s the general name for the dados and rabbets and grooves that we use to put together casework They are the under appreciated joints that make the woodworking world go round This 3 part video demonstrates how Traditional Handtool woodworking techniques are used by laying out and cutting the dado housing for the treads and rise
Cutting Housing Dados With Plow Plane
Cutting Housing Dados With Plow Plane
[img-1]
[img_title-2]
[img-2]
[img_title-3]
[img-3]
It will only cut a 32nd sixteenth deep without getting into adjusting the cutter depth but I then use that outline to chisel chop the groove or run a router plane along the outline depending on the workability of the grain Or chop the bulk of the groove with a chisel then run a router plane to clean up the bottom of the groove Position the guide to the outside of the dado with the edge directly on the layout line The knife point or edge of a chisel can be placed in the score line to help locate the guide Then clamp the guide down firmly As you saw down to the baseline concentrate on holding the blade square against the guide
T here are numerous ways to cut a dado by hand You can saw the walls and then clean out the waste with a chisel and router plane You can even make the joint with nothing but a sharp chisel These methods however are relatively slow Cutting Housing Dadoes The Case for Small Routers By Paul Sellers 5 June 2018 Hand routers come in a wide range of types and sizes wood and metal ones work the same and there are advantages as always to wood on wood
More picture related to Cutting Housing Dados With Plow Plane
[img_title-4]
[img-4]
[img_title-5]
[img-5]
[img_title-6]
[img-6]
Plough Plane Sharpening Setup Use Woodworking Masterclasses Posted 31 August 2018 Need to run some grooves and not sure where to start Paul shows how to sharpen and prepare the plough plane for use before showing the basics of how to cut a Start with short small strokes and apply lateral sideways pressure towards the side of the wood making the strokes longer each time Start at the end of the stock taking short shavings and then moving gradually backwards taking longer shavings
I want to use a plough plane stanley 45 to cut dadoes cross grain The spurs knickers are useful in preventing tearout and defining a clean knife wall but they score past the bottom of the dado like in the following image dado profile outlined in red You can cut dadoes with a plow plane but they are not the greatest at it If you do use a plow plane it helps to obtain a clean shoulder to knife the dado s shoulders prior to plowing The half inch will do me for a start as it will be doing 18 8 mm housing joints in 2 passes I l also be going over to have a drool on your site at the
[img_title-7]
[img-7]
[img_title-8]
[img-8]
https://www.youtube.com/watch?v=eljCzinSTkQ
Make a Dado Joint using a Router Plane w Bill Anderson Wood and Shop 229K subscribers Subscribe 1 4K 80K views 4 years ago Joinery Bill shows how to cut a dado joint for shelves and trim
https://www.renaissancewoodworker.com/planes-for-grooves-and-dados/
Joinery Techniques Dados Grooves and Router Plane Best Practices Watch on Grooves Dados Using Planes and Saws Housed joinery That s the general name for the dados and rabbets and grooves that we use to put together casework They are the under appreciated joints that make the woodworking world go round
[img_title-9]
[img_title-7]
[img_title-10]
[img_title-11]
[img_title-12]
[img_title-13]
[img_title-13]
[img_title-14]
[img_title-15]
[img_title-16]
Cutting Housing Dados With Plow Plane - It will only cut a 32nd sixteenth deep without getting into adjusting the cutter depth but I then use that outline to chisel chop the groove or run a router plane along the outline depending on the workability of the grain Or chop the bulk of the groove with a chisel then run a router plane to clean up the bottom of the groove
